Sony Flat Panel Television 32EX400 User Manual

4-174-286-13(1)  
Setting Up  
LCD  
Watching TV  
Digital Colour TV  
Operating Instructions  
Additional Information  
KDL-55HX700 / 55EX500 / 46HX700 / 46EX500 / 40HX700 / 40EX500 / 40EX400  
KDL-32EX500 / 32EX400  
 
Table of Contents  
• Operating instructions are built into your BRAVIA TV. Refer to “To use i-Manual” for operation (page 9).  
• Before operating the TV, please read “Safety Information” (page 16). Retain this manual for future reference.  
Checking the accessories  
AC power cord (mains lead)  
(for KDL-55/46EX500 and KDL-55/  
46HX700)  
Inserting batteries into the  
remote  
RM-GD009/GD014 remote  
Cable holder (1)  
(for HX700 models only)  
Remote (1)  
Size AAA batteries (R3 type) (2)  
Table-Top Stand (1)*  
Fixing screws for stand (M5 × 16) (4)  
Assembling screws for stand  
(M5 × 16) (4)  
(only for KDL-40/32EX500 and KDL-  
40HX700)  
Assembling screws for stand  
(M4 × 10) (3)  
(only for EX400 models)  
1
2
Remove the protection sheet.  
Push and slide the cover upward.  
RM-GD015 remote  
Push and lift the cover to open.  
* Disassembled except for 55-inch and 46-inch  
TVs. Refer to the supplied Table-Top Stand leaflet  
to assemble the stand.  
~
See your remote for the model number.  
3 GB  
 
     
Setting Up  
Adjusting the viewing angle of  
the TV (HX700 models only)  
This TV can be adjusted within the angles  
shown below.  
Attaching the Table-Top  
Stand  
~
For best picture quality, do not expose the screen  
to direct illumination or sunlight.  
0º  
6º  
If the TV is brought directly from a cold to a warm  
location, or is placed in a very damp room, or is  
placed in a room in which heating has just been  
turned on, moisture may condense on the surface  
or inside the TV. Should this occur, turn off the  
TV and leave the TV off until the moisture  
evaporates, and then the TV can be used. If you  
notice moisture condensation between the glass  
panel and the LCD, turn on the TV and the  
condensation will evaporate after the TV has  
warmed up.  
1
2
4
3
1 Refer to the supplied Table-Top Stand  
leaflet for proper attachment for some  
TV models.  
2 Place the TV set on the Table-Top  
Stand.  
Remove screw as  
shown.  
Install screw into  
the top screw hole  
of the Table-Top  
Stand.  
3 Fix the TV to the Table-Top Stand  
according to the arrow marks that  
guide the screw holes using the  
supplied screws.  
Lift up and tilt.  
Slide in.  
~
To return to 0°, reverse the above procedure.  
~
If using an electric screwdriver, set the tightening  
torque at approximately 1.5 N·m {15 kgf·cm}.  
4GB  
 
   
Connecting an antenna (aerial)/cable  
and VCR  
Connecting an antenna  
(aerial)/cable/VCR  
Connecting an antenna (aerial)/cable  
Antenna  
(aerial) cable  
(not supplied)  
Antenna (aerial) cable  
(not supplied)  
AV cable  
(not supplied)  
Antenna  
(aerial) cable  
(not supplied)  
VCR  
~
When connecting an antenna (aerial) cable (not  
supplied), an adaptor (not supplied) may be  
required (Australian model and New Zealand  
model only).  
5 GB  
 
 
Preventing the TV from  
toppling over  
Bundling the cables  
~
A cable holder is available for HX700 models. To  
bundle the cables, follow steps 2 to 4.  
* For KDL-55/46EX500  
and KDL-55/46HX700  
*
~
1 Install a wood screw (4 mm in  
Do not bundle the AC power cord (mains lead)  
together with other cables.  
diameter, not supplied) in the TV stand.  
2 Install a machine screw (M4 × 16, not  
supplied) into the screw hole of the TV.  
3 Tie the wood screw and the machine  
screw with a strong cord (not supplied).  
z
An optional Sony support belt kit is used to secure  
the TV. Contact your nearest Sony service centre  
to purchase a kit. Have your TV model name  
ready for reference.  
6GB  
 
   
Performing the initial set-up  
Detaching the Table-Top  
Stand from the TV  
~
Remove the screws guided by the arrow marks  
of the TV.  
Do not remove the Table-Top Stand for any  
reason other than to install corresponding  
accessories on the TV.  
For HX700 models  
only  
1 Connect the TV to your AC power  
outlet (mains socket).  
2 For HX700 models, check the  
ENERGY SAVING SWITCH setting  
is on (z).  
3 Press 1 on the TV.  
When you switch on the TV for the first  
time, the Language menu appears on the  
screen.  
4
Follow the instructions on the screen.  
Programme Sorting: Changes the order of  
analogue channels stored in the TV.  
1 Press F/f to select the channel you want  
to move to a new position, then press  
.
2 Press F/f to select the new position for  
the channel, then press  
.
~
You can also tune channels manually.  
7 GB  
 
   
Watching TV  
To watch programmes  
Turn on the TV.  
1
2
GUIDE  
1 For HX700 models, switch ENERGY  
SAVING SWITCH on.  
2 Press 1 on the TV to turn on the TV.  
OPTIONS  
HOME  
Select a mode.  
2
3
Select a TV channel.  
3
Using Digital Electronic Programme  
Guide (only available for EPG  
supported countries/regions)  
z
Press GUIDE in digital mode to display the  
programme guide.  
The number 5, N, PROG + and AUDIO  
buttons on the remote have a tactile dot.  
Use the tactile dots as a reference when  
operating the TV.  
To utilise the TV's features  
HOME button  
OPTIONS button  
Press to display various operation and setting  
screens.  
Press to display convenient functions based  
on the current input or content.  
Picture  
Sound  
BRAVIA ENGINE  
3
PRO  
Add to Favourites  
Lock/Unlock  
PAP  
Settings  
System Settings  
Motionflow  
Sleep Timer  
Headphone Volume  
Speaker  
System Information  
TV  
8GB  
 
     
To use i-Manual  
Operating instructions are built into your BRAVIA  
TV and can be displayed on the screen.  
You can browse your i-Manual anytime you need  
to find the varieties of convenient functions.  
1
2
~
This feature is unavailable when you select Arabic or  
Persian.  
Press i-MANUAL.  
1
Press G/g/F/f/ to select items.  
2
x Welcome to i-Manual  
x “BRAVIA” TV Features  
x Watching TV  
x Fun Features with Connected  
Equipment  
Introduces how to connect optional equipment.  
x Parts Description  
Introduces convenient features such as EPG  
Guide, Favourites, etc.  
x Troubleshooting  
Find solutions for your problem.  
x Using the HOME Menu  
Customise your TV settings, etc.  
x Index  
~
Images and illustrations may differ from what is displayed on the screen.  
9 GB  
 
   
Additional Information  
Troubleshooting  
Check whether the 1 (standby) indicator is flashing in red.  
When the 1 (standby) indicator is flashing  
The self-diagnosis function is activated.  
1 Count how many times the 1 (standby) indicator flashes between each three second  
break.  
For example, the indicator may flash three times, go off for three seconds, then flash again three  
times.  
2 Press 1 on the TV to turn it off, disconnect the AC power cord (mains lead), and inform  
your dealer or Sony service centre of how the indicator flashes (number of flashes).  
When the 1 (standby) indicator is not flashing  
1 Check the items in the tables below. (Also refer to “Troubleshooting” in the i-Manual.)  
2 If the problem persists, have your TV serviced by qualified service personnel.  
Condition  
Explanation/Solution  
Picture  
There is no picture (screen Check the antenna (aerial)/cable connection.  
Connect the TV to the AC power (mains), and press 1 on the TV.  
If the 1 (standby) indicator lights up in red, press "/1.  
is dark) and no sound.  
Tiny black points and/or  
bright points appear on the  
screen.  
The screen is composed of pixels. Tiny black points and/or bright  
points (pixels) on the screen do not indicate a malfunction.  
General  
The TV’s power cannot be Check if ENERGY SAVING SWITCH is on.  
turned on. (for HX700  
models only)  
The TV turns off  
automatically (the TV  
enters standby mode).  
Check if the “Sleep Timer” is activated, or confirm the  
“Duration” setting of “On Timer”.  
Check if the “Idle TV Standby” is activated.  
The remote does not  
function.  
Replace the batteries.  
Your TV may be in SYNC mode.  
Press SYNC MENU, select “TV Control” and then select “Home  
(Menu)” or “Options” to control the TV.  
The “Parental Lock” password  
has been forgotten.  
Enter 9999 for the PIN code. (PIN code 9999 is always accepted.)  
10GB  
 
   
Specifications  
System  
LCD (Liquid Crystal Display) Panel  
Panel system  
TV system  
Analogue: B/G, I, D/K, M  
Digital: DVB-T  
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video  
input)  
Digital: MPEG-2 MP@ML/HL (Australian model),  
MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC MP/HP@L4 (New Zealand and  
Singaporean model)  
Colour/video system  
Channel coverage  
Analogue:B/G: VHF: E2–E12/UHF: E21–E69/CATV: S01–S03, S1–S41  
VHF: 0–12, 5A, 9A/UHF: 28–69/CATV: S01–S03, S1–S44  
(Australia and Singapore only)  
VHF: 1–11/UHF: 21–69/CATV: S1–S41  
(New Zealand and Singapore only)  
I:  
UHF: B21–B69/CATV: S01–S03, S1–S41  
(Australia, New Zealand and South Africa only)  
D/K: VHF: C1–C12, R1–R12/UHF: C13–C57, R21–R60/CATV: S01–S03,  
S1–S41, Z1–Z39 (Australia, New Zealand and South Africa only)  
M: VHF: A2 to A13/ UHF: A14 to A79/ CATV: A-8 to A-2, A to W+4, W+6  
to W+84 (South Africa only)  
Digital: VHF/UHF (Australia and Singapore only), UHF (New Zealand only)  
10 W + 10 W  
Sound output  
Input/Output jacks  
75 ohm external terminal for VHF/UHF  
Video input (phono jack)  
Antenna (aerial)/cable  
1, 2  
1, 2  
1, 2  
Audio input (phono jacks)  
COMPONENT IN  
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i  
3 Video input (phono jack)  
/
3
Video: 1080/24p, 1080p, 1080i, 720p, 576p, 576i, 480p, 480i  
Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital  
Analogue audio input (minijack) (HDMI IN4 only)  
PC Input  
HDMI IN1, 2, 3, 4  
Digital optical jack (Two channel linear PCM, Dolby Digital)  
Audio output (phono jacks)  
DIGITAL AUDIO OUT (OPTICAL)  
(VAR/FIX)  
PC IN  
PC Input (Mini D-sub 15-pin)  
PC audio input (minijack)  
USB port  
Headphones jack  
i
10BASE-T/100BASE-TX connector (Depending on the operating environment of the  
network, connection speed may differ. 10BASE-T/100BASE-TX communication rate  
and communication quality are not guaranteed for this TV.)  
LAN  
(for HX700 models only)  
* For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).  
(Continued) 11GB  
 
 
Model name KDL-  
Power and others  
Power requirements  
55EX500  
55HX700  
46EX500  
46HX700  
110 V – 240 V AC, 110 V – 240 V AC, 110 V – 240 V AC, 110 V – 240 V AC,  
50/60 Hz 50 Hz 50/60 Hz 50 Hz  
55 inches (Approx. 138.8 cm)  
46 inches (Approx. 116.8cm)  
Screen size (measured diagonally)  
Display resolution  
1,920 dots (horizontal) × 1,080 lines (vertical)  
1,324 mm ×  
1,363 mm ×  
1,127 mm ×  
1,154 mm ×  
Dimensions  
(Approx.)  
with Table-Top Stand  
832 mm × 350 mm 862 mm × 400 mm 713 mm × 281 mm 741 mm × 370 mm  
1,324 mm × 1,363 mm × 1,127 mm × 1,154 mm ×  
795 mm × 105 mm 825 mm × 105 mm 676 mm × 101 mm 704 mm × 102 mm  
(w × h × d)  
without Table-Top Stand  
30.7 kg  
26.7 kg  
40.2 kg  
34.4 kg  
21.6 kg  
18.7 kg  
28.4 kg  
24.3 kg  
Mass(Approx.) with Table-Top Stand  
without Table-Top Stand  
SU-WL500/WL50B  
Supplied accessories  
Optional  
Wall-Mount Bracket  
accessories  
Model name KDL-  
Power and others  
Power requirements  
40EX400  
40EX500  
40HX700  
32EX400  
32EX500  
110 V – 240 V AC, 50/60 Hz  
40 inches (Approx. 101.6cm)  
110 V – 240 V 110 V – 240 V AC, 50/60 Hz  
AC, 50 Hz  
32 inches (Approx. 80.1 cm)  
Screen size (measured diagonally)  
Display resolution  
1,920 dots (horizontal) × 1,080 lines (vertical)  
992 mm ×  
635 mm ×  
250 mm  
992 mm ×  
636 mm ×  
260 mm  
1,023 mm ×  
665 mm ×  
310 mm  
800 mm ×  
532 mm ×  
220 mm  
800 mm ×  
534 mm ×  
250 mm  
Dimensions  
(Approx.)  
(w × h × d)  
with Table-Top Stand  
992 mm ×  
598 mm ×  
100 mm  
992 mm ×  
599 mm ×  
99 mm  
1,023 mm ×  
628 mm ×  
100 mm  
800 mm ×  
497 mm ×  
97 mm  
800 mm ×  
497 mm ×  
96 mm  
without Table-Top Stand  
15.9 kg  
13.9 kg  
16.4 kg  
14.2 kg  
22.4 kg  
19.2 kg  
11.0 kg  
9.5 kg  
11.9 kg  
9.9 kg  
Mass(Approx.) with Table-Top Stand  
without Table-Top Stand  
SU-WL500/WL50B  
Supplied accessories  
Optional  
Wall-Mount Bracket  
accessories  
Design and specifications are subject to change without notice.  
12GB  
 
Installing the Accessories (Wall-Mount Bracket)  
To Customers:  
For product protection and safety reasons, Sony strongly recommends that installing of your TV be  
performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.  
To Sony Dealers and Contractors:  
Provide full attention to safety during the installation, periodic maintenance and examination of this  
product.  
Your TV can be installed using the SU-WL500 or SU-WL50B Wall-Mount Bracket (sold  
separately).  
Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the  
installation.  
~
Place the TV on the Table-Top Stand, when securing the Mounting Hook.  
SU-WL500  
SU-WL50B  
Screw  
(+PSW  
6 × 16)  
Screw  
(+PSW  
6 × 16)  
Square  
hole  
Mounting Hook  
Mounting Hook  
Sufficient expertise is required for installing this product, especially to determine the strength of  
the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the  
wall to Sony dealers or licensed contractors and pay adequate attention to safety during the  
installation. Sony is not liable for any damage or injury caused by mishandling or improper  
installation.  
(Continued) 13GB  
 
 
TV installation dimensions table  
SU-WL500  
Screen centre point  
SU-WL50B  
Screen centre point  
Unit: mm  
Screen  
Display  
Length for each mounting angle  
Angle (0°) Angle (20°)  
centre  
dimensions  
dimension  
Model Name  
KDL-  
C
D
E
F
G
H
A
B
SU-  
SU-  
SU-  
SU-  
SU-  
SU-  
SU-WL500 only  
WL500 WL50B WL500 WL50B WL500 WL50B  
1,324  
1,363  
1,127  
1,154  
992  
795  
825  
676  
704  
598  
599  
628  
497  
497  
25  
25  
78  
428  
439  
426  
439  
425  
426  
439  
426  
426  
481  
492  
478  
492  
478  
479  
492  
454  
454  
165  
165  
161  
162  
160  
159  
160  
157  
156  
166  
166  
162  
163  
161  
160  
160  
158  
157  
413  
421  
369  
377  
341  
341  
349  
303  
303  
752  
776  
640  
662  
567  
567  
591  
470  
470  
466  
481  
463  
480  
463  
463  
479  
461  
461  
55EX500  
78  
55HX700  
46EX500  
46HX700  
40EX400  
40EX500  
40HX700  
32EX400  
32EX500  
84  
137  
137  
175  
175  
175  
200  
200  
84  
122  
122  
122  
172  
172  
992  
1,023  
800  
800  
Figures in the above table may differ slightly depending on the installation.  
WARNING  
The wall that the TV will be installed on should be capable of supporting a weight of at least four  
times that of the TV. Refer to “Specifications” (page 11) for its weight.  
14GB  
 
Screw and Hook locations diagram/table  
Screw location  
Hook location  
Model Name  
SU-WL500  
SU-WL50B  
SU-WL500  
SU-WL50B  
KDL-55HX700 / 55EX500  
a
b
c
d, g  
d, i  
KDL-46HX700 / 46EX500  
KDL-40HX700 / 40EX500 / 40EX400  
KDL-32EX500 / 32EX400  
e, g  
e, h  
SU-WL500  
Screw location  
Hook location  
When installing the Mounting Hook on the  
TV.  
When installing the TV onto the Base Bracket.  
a
b
c
SU-WL50B  
Screw location  
Hook location  
When installing the Mounting Hook on the  
TV.  
When installing the TV onto the Base Bracket.  
a
b
c
a
b
c
c
b
a
Mounting Hook  
Base Bracket  
15GB  
 
AC power cord  
Handle the AC power cord and outlet as  
follows in order to avoid any risk of fire,  
electrical shock or damage and/or injuries:  
Safety  
Information  
Use only Sony supplied AC power  
cords, not those of other brands.  
Insert the plug fully into the AC power  
outlet.  
Operate the TV set on a 110–240 V AC  
supply only.  
When wiring cables, be sure to unplug  
the AC power cord for your safety and  
take care not to catch your feet on the  
cables.  
Installation/Set-up  
Install and use the TV set in accordance  
with the instructions below in order to  
avoid any risk of fire, electrical shock or  
damage and/or injuries.  
Installation  
• The TV set should be installed near an  
easily accessible AC power outlet.  
• Place the TV set on a stable, level surface  
to avoid it from falling down and cause  
personal injury or damage to the TV.  
• Only qualified service personnel should  
carry out wall installations.  
Ventilation  
• Never cover the ventilation holes or  
insert anything in the cabinet.  
• Leave space around the TV set as shown  
below.  
Disconnect the AC power cord from  
the AC power outlet before working on  
or moving the TV set.  
• It is strongly recommended that you use  
a Sony wall-mount bracket in order to  
provide adequate air-circulation.  
Keep the AC power cord away from  
heat sources.  
Unplug the AC power plug and clean it  
regularly. If the plug is covered with  
dust and it picks up moisture, its  
insulation may deteriorate, which could  
result in a fire.  
• For safety reasons, it is strongly  
recommended that you use Sony  
accessories, including:  
Installed on the wall  
30 cm  
Wall-mount bracket SU-WL500/  
WL50B  
10 cm  
10 cm  
• Be sure to use the screws supplied with  
the Wall-mount bracket when attaching  
the mounting hooks to the TV set. The  
supplied screws are designed so that they  
are 8 mm to 12 mm in length when  
measured from the attaching surface of  
the mounting hook.  
The diameter and length of the screws  
differ depending on the Wall-mount  
bracket model.  
Notes  
• Do not use the supplied AC power cord  
on any other equipment.  
• Do not pinch, bend, or twist the AC  
power cord excessively. The core  
conductors may be exposed or broken.  
• Do not modify the AC power cord.  
• Do not put anything heavy on the AC  
power cord.  
• Do not pull on the AC power cord itself  
when disconnecting the AC power cord.  
• Do not connect too many appliances to  
the same AC power outlet.  
• Do not use a poor fitting AC power  
outlet.  
10 cm  
Leave at least this space around  
the set.  
Installed with stand  
Use of screws other than those supplied  
may result in internal damage to the TV  
set or cause it to fall, etc.  
30 cm  
10 cm  
10 cm  
6 cm  
8 mm - 12 mm  
Screw (supplied with the  
Wall-mount bracket)  
Leave at least this space around  
the set.  
Prohibited Usage  
Do not install/use the TV set in locations,  
environments or situations such as those  
listed below, or the TV set may  
Mounting Hook  
• To ensure proper ventilation and prevent  
the collection of dirt or dust:  
Hook attachment on rear  
of TV set  
malfunction and cause a fire, electrical  
shock, damage and/or injuries.  
Do not lay the TV set flat, install  
upside down, backwards, or  
sideways.  
Transporting  
Location:  
• Before  
Do not place the TV set on a shelf,  
rug, bed or in a closet.  
Do not cover the TV set with a  
cloth, such as curtains, or items  
such as newspapers, etc.  
transporting the  
TV set,  
disconnect all  
cables.  
• Two or three  
people are  
needed to  
transport a large  
TV set.  
• When transporting the TV set by hand,  
hold it as shown on the right. Do not put  
stress on the LCD panel and the frame  
around the screen.  
• When lifting or moving the TV set, hold  
it firmly from the bottom.  
Outdoors (in direct sunlight), at the  
seashore, on a ship or other vessel, inside a  
vehicle, in medical institutions, unstable  
locations, near water, rain, moisture or  
smoke.  
Do not install the TV set as shown  
below.  
Environment:  
Places that are hot, humid, or excessively  
dusty; where insects may enter; where it  
might be exposed to mechanical vibration,  
near flammable objects (candles, etc). The  
TV set shall not be exposed to dripping or  
splashing and no objects filled with liquids,  
such as vases, shall be placed on the TV.  
Air circulation is blocked.  
Wall  
Wall  
• When transporting the TV set, do not  
subject it to jolts or excessive vibration.  
Situation:  
Do not use when your hands are wet, with  
the cabinet removed, or with attachments  
not recommended by the manufacturer.  
Disconnect the TV set from AC power  
outlet and antenna during lightning storms.  
• When transporting the TV set for repairs  
or when moving, pack it using the  
original carton and packing material.  
16GB  
 
   
Batteries  
Broken pieces:  
• Observe the correct polarity when  
inserting batteries.  
• Do not throw anything at the TV set. The  
screen glass may break by the impact and  
cause serious injury.  
Precautions  
Viewing the TV  
• View the TV in moderate light, as  
viewing the TV in poor light or during  
long period of time, strains your eyes.  
• When using headphones, adjust the  
volume so as to avoid excessive levels, as  
hearing damage may result.  
• Do not use different types of batteries  
together or mix old and new batteries.  
• Dispose of batteries in an  
environmentally friendly way. Certain  
regions may regulate the disposal of  
batteries. Please consult your local  
authority.  
• Handle the remote with care. Do not drop  
or step on it, or spill liquid of any kind  
onto it.  
• Do not place the remote in a location near  
a heat source, a place subject to direct  
sunlight, or a damp room.  
• If the surface of the TV set cracks, do not  
touch it until you have unplugged the AC  
power cord. Otherwise electric shock  
may result.  
When not in use  
• If you will not be using the TV set for  
several days, the TV set should be  
disconnected from the AC power for  
environmental and safety reasons.  
• As the TV set is not disconnected from  
the AC power when the TV set is just  
turned off, pull the plug from the AC  
power outlet to disconnect the TV set  
completely.  
• However, some TV sets may have  
features that require the TV set to be left  
in standby to work correctly.  
LCD Screen  
• Although the LCD screen is made with  
high-precision technology and 99.99% or  
more of the pixels are effective, black  
dots may appear or bright points of light  
(red, blue, or green) may appear  
Disposal of the TV set  
(Australian model only)  
constantly on the LCD screen. This is a  
structural property of the LCD screen and  
is not a malfunction.  
• Do not push or scratch the front filter, or  
place objects on top of this TV set. The  
image may be uneven or the LCD screen  
may be damaged.  
• If this TV set is used in a cold place, a  
smear may occur in the picture or the  
picture may become dark. This does not  
indicate a failure. These phenomena  
disappear as the temperature rises.  
• Ghosting may occur when still pictures  
are displayed continuously. It may  
disappear after a few moments.  
• The screen and cabinet get warm when  
this TV set is in use. This is not a  
malfunction.  
• The LCD screen contains a small amount  
of liquid crystal. Some fluorescent tubes  
used in this TV set also contain mercury.  
Follow your local ordinances and  
regulations for disposal.  
Disposal of Old  
Electrical &  
Electronic  
For children  
• Do not allow children to climb on the TV  
set.  
• Keep small accessories out of the reach  
of children, so that they are not  
mistakenly swallowed.  
Equipment  
(Applicableinthe  
European Union  
and other  
European countries with  
separate collection  
systems)  
This symbol is on the remote control.  
If the following problems  
occur...  
Turn off the TV set and unplug the AC  
power cord immediately if any of the  
following problems occur.  
Ask your dealer or Sony service centre to  
have it checked by qualified service  
personnel.  
Handling and cleaning the  
screen surface/cabinet of  
the TV set  
Be sure to unplug the AC power cord  
connected to the TV set from AC power  
outlet before cleaning.  
When:  
AC power cord is damaged.  
Poor fitting of AC power outlet.  
TV set is damaged by being dropped,  
hit or having something thrown at it.  
Any liquid or solid object falls through  
openings in the cabinet.  
To avoid material degradation or screen  
coating degradation, observe the following  
precautions.  
• To remove dust from the screen surface/  
cabinet, wipe gently with a soft cloth. If  
dust is persistent, wipe with a soft cloth  
slightly moistened with a diluted mild  
detergent solution.  
• Do not spray water or detergent directly  
on the TV set.  
It may drip to the bottom of the screen or  
exterior parts, and may cause a  
malfunction.  
• Never use any type of abrasive pad,  
alkaline/acid cleaner, scouring powder,  
or volatile solvent, such as alcohol,  
benzene, thinner or insecticide. Using  
such materials or maintaining prolonged  
contact with rubber or vinyl materials  
may result in damage to the screen  
surface and cabinet material.  
• Periodic vacuuming of the ventilation  
openings is recommended to ensure to  
proper ventilation.  
• When adjusting the angle of the TV set,  
move it slowly so as to prevent the TV set  
from moving or slipping off from its  
table stand.  
Optional Equipment  
Keep optional components or any  
equipment emitting electromagnetic  
radiation away from the TV set. Otherwise  
picture distortion and/or noisy sound may  
occur.  
17GB  
 
 
 
 
Instructions about “Installing Wall Mount Bracket” are included  
within this TV’s instructions manual.  
Customer Support:  
4-174-286-13(1)  
© 2010 Sony Corporation  
Printed in Malaysia  
 

Sharp Projector PG LS2000 User Manual
Solid State Logic Stereo Amplifier 82S6XL020E User Manual
Sony Car Video System MV 7101DS User Manual
Sony Printer 327 User Manual
Sony Projector PSS 2000 User Manual
Sony Projector VPL VW90ES User Manual
Sterling Plumbing Indoor Furnishings 11605 NA User Manual
Stiga Automobile Parts 8211 0202 11 User Manual
Stoelting Freezer E157 User Manual
SUPER MICRO Computer Life Jacket 6025B 3 User Manual